Skunk 2 Cold Air Intake - 343-05-0100
Bent Type
J-Bend
Estimated Install Time (Hours)
1
Filter Color
Red
Protection Type
No Protection
Recommended Use
Racing
Tube Color
Black
Tube Finish
Matte
Tube Material
Polymer Plastic
Share this page
Skunk 2 Cold Air Intake
Cold Air Intake; Polymer Plastic; Red Cone Filter; With Silicone Adapters And Mounting Hardware
MPN: 343050100
Skunk2 drew upon its experience and longstanding technical partnership with championship-winning Compass360 Racing when developing its all-new Cold-Air Intake for the 2006 to 2011 Civic Si. The results are the best performing, best fitting intake system available. Skunk2’s Cold-Air Intake is manufactured from molded polymer plastic for superior intake air insulation when compared to aluminum as well as for a smooth, continuous taper. When compared to aluminum, the thicker polymer material results in a superior thermal barrier and lower intake air temperatures. Each kit includes a 3.5 Inch internal diameter lower tube and a tapered, 3.5 Inch to 3.0 Inch internal diameter upper tube that connects to the factory throttle body with a high-quality, silicone connector (larger diameter connector for use with Skunk2 throttle bodies or similar sold separately). The two-piece design and supplied MAF sensor adapter allows for compatibility with vehicles utilizing the factory ECU. A silicone coupler featuring a smooth, tapered transition between the two tubes is also included for vehicles equipped with aftermarket engine management systems that don’t utilize MAF sensors. In an effort to reduce the possibility of submerging the air filter during wet conditions, Skunk2’s design positions the air filter downward-facing for approximately two inches of additional ground clearance when compared to competitors’ designs that locate the air filter from the side. That, combined with a design that doesn’t require cutting or modifying the factory fender liners, greatly reduces the chances of water entering the intake during wet conditions. Each Cold-Air Intake kit includes relocation hardware for the battery, ECU, fuse box, and cooling system reservoir tank as well as high-quality stainless steel clamps and mounting hardware. Unlike other intake systems, only Skunk2’s unique design and brackets allow for the OEM battery to be retained.
Recommended Use: Racing
Bent Type: J-Bend
Tube Finish: Matte
Tube Color: Black
Tube Material: Polymer Plastic
Filter Color: Red
Protection Type: No Protection
Estimated Install Time (Hours): 1
Features
- Thick Polymer Material Results In A Superior Thermal Barrier And Lower Intake Air Temperatures
- Includes A 3.5 Inch Internal Diameter Lower Tube And A Tapered, 3.5 Inch To 3.0 Inch Internal Diameter Upper Tube That Connects To The Factory Throttle Body With A High-Quality, Silicone Connector
- The Two-Piece Design And Supplied MAF Sensor Adapter Allows For Compatibility With Vehicles Utilizing The Factory ECU
- A Silicone Coupler Featuring A Smooth, Tapered Transition Between The Two Tubes Is Also Included For Vehicles Equipped With Aftermarket Engine Management Systems That Don’t Utilize MAF Sensors
- The Design Positions The Air Filter Downward-Facing For Approximately 2 Inch Of Additional Ground Clearance
- Doesn’t Require Cutting Or Modifying The Factory Fender Liners, Greatly Reduces The Chances Of Water Entering The Intake During Wet Conditions
- Limited 1 Year Warranty
Specifications of Skunk 2 Cold Air Intake - 343-05-0100 | |
Bent Type | J-Bend |
Estimated Install Time (Hours) | 1 |
Filter Color | Red |
Protection Type | No Protection |
Recommended Use | Racing |
Tube Color | Black |
Tube Finish | Matte |
Tube Material | Polymer Plastic |
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
No questions found. Be the first?
Reviews for Skunk 2 Cold Air Intake - 343-05-0100(0)
There are no reviews for this product.